Operation
Once the AB 1 is properly connected and the levels have been set, operation is simple. In order to use the AB 1 module, the A-BUS/Ready receiver must be turned on and placed in the Multiroom mode. The procedure for doing this will vary from model to model, so we suggest that you consult the owner�s manual for your receiver for the correct instructions. As long as the receiver is powered up, and the Multiroom system is turned on, the AB 1�s amplifier may be turned on by simply pointing the Zone II remote supplied with the unit, or any remote programmed with the proper Harman Kardon IR codes, at the AB 1�s IR Sensor 4 and pressing the remote�s Power On button. You may adjust the volume in the remote room by pressing the Volume Up/Down Buttons 3 on the AB 1 or with the volume control buttons on the remote. The remote may also be used to operate the receiver to change sources and make other adjustments, such as changing the station on the tuner. When the proper IR codes are programmed in the remote being used, you may also operate compatible source components, such as CD or DVD players, that are connected to the IR remote output jack on the receiver. To turn the remote room feed off, press the OFF button on the Zone II or other properly programmed remote.
Specifications
� Wire type required: Category 5/5e (or better) cable in compliance with any applicable local building code or NEC requirements for in-wall, riser or plenum use. � Wiring protocol: TIA wiring specification for T568A at the A-BUS/Ready product end. Connections at the AB 1 are specified on the AB 1. � Connection terminals: IDT type for Category 5/5e wire, screw terminal type for speaker connections. � Speaker wire: Maximum AWG 14, in compliance with any applicable local building code or NEC requirements for in-wall, riser or plenum use. � Speaker impedance: Suitable for connection to speakers with nominal 6 ohms to 8 ohms impedance. � Speaker sensitivity: Optimized for speakers with sensitivity above 88dB. � Infrared compatibility: 38kHz and 56kHz, with talkback � Dimensions (H x W x D): 4-1/4" x 1-3/4" x 2-1/4" � Weight: 0.25 lb
Step Three: Connect the Category 5/5e cable to the AB 1. Once the wire is run to the remote location where the AB 1 will be installed, connect the Category 5/5e cable to the AB 1. Prior to making the connections, strip the outer jacket of the Cat. 5/5e cable 1-1/2" to 2" from the end, taking care not to nick the inner conductors. Next, separate the four twisted pairs within the cable and then untwist the ends of each pair about 1/2." All terminations are made at the Input Cable Connection Block ¡. Connect the wires using standard Insulation Displacement Terminal (IDT) tools and procedures. DO NOT use screwdrivers to insert the wire into the IDT connection points. Also, take special care to make certain that there are no shorts between any of the individual wires, as this may cause damage to the AB 1. From left to right, the connections are made as follows:
So that the level adjustments are as accurate as possible, select a program source or music type that is representative of what will most often be listened to in the room where the A-BUS module will be installed. Step Six: Adjust the output levels. This step sets the level adjustments for the AB 1. Once this process is complete, all further volume settings are made with the Volume Up/Down Buttons 3 on the AB 1, the Zone II remote, or an optional third-party remote that is programmed for Harman Kardon products. With the Multiroom system activated and a source playing, press the Volume Up Button 3 for 20 seconds so that the AB 1�s volume is set at its maximum. Next, adjust each of the Output Level Trims � until the output begins to clip. At this point, back the trim control down in the opposite direction until the clipping stops. This is the correct level for your specific A-BUS/ Ready receiver and AB 1. Before proceeding further, lower the volume back to normal listening level using the Volume Down Button 3. Step Seven: Install the AB 1. Place the AB 1 in the junction box or plaster ring, making sure that any loose wire is carefully secured inside the wall or box, and that there are no shorts between any of the connections.
� Brown � White w/Brown Stripe � Blue � White w/Blue Stripe � Green � White w/Green Stripe � Orange � White w/Orange Stripe
Troubleshooting Guide
If you cannot hear any sound from the speakers connected to the AB 1: � Make certain that the Cat. 5/5e cable is properly connected to both the AB 1 and receiver. � Make certain that the receiver is turned on and that the Multiroom mode is properly activated. � Make certain that any needed volume-level adjustments on the receiver are properly made. � Make certain that the volume control on the AB 1 is turned up. � Check for proper adjustments of the output level trims. � Check the speaker connections. If the receiver or other components do not respond to commands from the AB 1 or a remote pointed at the AB 1: � Make certain that the A-BUS/Ready receiver�s Multiroom system has been turned on. � Make certain that the Cat. 5/5e cable is properly connected to both the AB 1 and receiver. � Make certain that there is a proper connection between the A-BUS/Ready receiver and any additional IR controlled components. � Make certain that the remote is properly programmed to operate the receiver and other components.
BR BR BL BL GR GR OR OR WH WH WH WH
Speaker Terminal Block
Output Level Trims Input Cable Connection Block
Step Four: Connect the speaker cable to the AB 1. Connect speaker wires to the AB 1 module using the colorcode chart on the Speaker Terminal Block £ as a guide. Be careful to properly observe the positive (+) and negative (�) polarity indications, and to avoid having the wire strands from one cable touch another. Insert the wire into the terminal block. Tighten the retaining screws to secure the wire.
Cover Plate & 2 Screws (not included)
Front Panel
J-Box 1/8" x 3/4" Machine Screws (2) (included)
Wallboard
Using the supplied mounting screws, attach the AB 1 to the junction box or plaster ring through the Screw Slots 2.
Amplified In-Wall Module
250 Crossways Park Drive, Woodbury, New York 11797 516.422.HKHK (4545) Fax: 516.682.3523
© 2003 Harman International Industries, Incorporated Printed 10/03 Part No. ABO 42hl
Harman Kardon is a registered trademark of Harman International Industries, Incorporated. A-BUS and A-BUS/Ready are registered trademarks of LeisureTech Electronics Pty Ltd. Australia. Decora is a registered trademark of Leviton Manufacturing Company, Inc. All features and specifications are subject to change without notice.
AB 1
®
Note that one wire in each pair is always a solid color, and the other is either white or striped. Make sure that the twisted pairs of wires consist of those attached to pins 1 and 2, pins 3 and 6, pins 4 and 5, and pins 7 and 8. When making the connections at each end of the cable, strip the outer insulation jacket about 1-1/2" to 2" from the end. The cable is constructed of four twisted pairs of wires as indicated above. Flatten the wire ends to prepare them for insertion into the connector. Fully insert the wire into the connector, being certain to check the color codes of the pin assignments one last time. Carefully crimp the connector, making sure that each wire is securely fastened.
Step Five: Connecting the AB 1 to the A-BUS/Ready product. To set the output trims, the AB 1 must first be connected to the A-BUS/Ready receiver. After first checking to make certain that the connections to the speaker cable and Cat. 5/5e cable have properly been made, plug the RJ-45 jack at the receiver end of the cable into the A-BUS jack on the back of the A-BUS/Ready receiver. Next, turn on the receiver and make any adjustments required to turn on the Multiroom system and send an active source to the output. As a confirmation that the connections have been made and that receiver is on, the Status LED 5 will light up.
Attach a Decora-style wall plate (not included) through the AB 1�s Screw Holes 1. Although any color Decora wall plate may be used with the AB 1, the AB 1 itself should not be painted.
Other notes on using the AB 1 and other A-BUS products with Harman Kardon A-BUS/Ready receivers: � When using the AB 1 with Harman Kardon A-BUS/Ready products, you may connect only one AB 1 at a time unless optional, external A-BUS-powered hub equipment is used. � If A-BUS keypads or other A-BUS accessories not specifically designed for use with Harman Kardon products are used, their operation may be slightly different than with the AB 1. Consult the support area of the Harman Kardon Web site at www.harmankardon.com.
Power for the Digital Revolution.
®
